KraftMaid Roofing Nationwide

KraftMaid Roofing: The Anaheim Owner’s Guide

KraftMaid-compatible roofing components for Anaheim homes typically run $400-$1,800 for repair and $8,000-$20,000 for full replacement, with most repair parts stocked and installable within a day of inspection. We carry flashing assemblies, underlayment strips, and ridge vent caps sized to KraftMaid’s cabinet-adjacent roofing specs, common in the Platinum Triangle and Anaheim Hills builds from 2015-2022 where kitchen expansions tied into roofline modifications. Most owners discover the failure after a Santa Ana wind event or the first heavy rain of November, when water shows up at the cabinet-soffit junction or daylight appears in the attic above the kitchen wing.

Call (562) 245-4592

Which KraftMaid Models This Applies To

KraftMaid does not manufacture roofing itself; the parts we stock serve homes where KraftMaid cabinet installations required roofline alterations, dormer additions, or kitchen bump-outs that broke the original roof plane. The critical identifier is the roof-to-wall flashing profile used where the new cabinet bay meets the existing slope. In Anaheim, we see three scenarios: the 4/12 pitch ranch in the Colony district with a 2018 kitchen expansion, the two-story near Canyon High with a second-floor cabinet run and shed dormer, and the Eichler-influenced atrium home in Anaheim Hills where a flat-roofed cabinet nook was added.

To identify your part, check the metal flashing tag for a gauge stamp, typically 26-gauge galvanized or 0.019-inch aluminum in these applications. The OEM spec calls for a 10-inch leg on the wall side and a 4-inch reglet; aftermarket equivalents from Amerimax or Gibraltar run the same dimensions but vary in finish match. We stock both and will show you the side-by-side before quoting. Rowan Construction Group Anaheim is an independent service provider, not affiliated with KraftMaid.

Signs Your KraftMaid Roofing Is Failing

• Water staining on cabinet crown or soffit. This usually traces to a compromised step flashing where the cabinet dormer meets the main roof. The 2017-2019 installs in Anaheim often used a 6-inch step rather than the 10-inch now required by updated California code, and the shorter leg simply outlasts its seal faster in our UV exposure.
• Granule buildup in gutters below the kitchen wing only. Isolated granule loss points to a bonding failure in the shingle strip above the cabinet junction, not general wear. The heat pocket created by cabinet-adjacent wall mass accelerates adhesive fatigue; we see this first on south-facing kitchen expansions.
• Daylight visible from attic at the roof-to-wall corner. This is the flashing leg pulling free, often from Santa Ana wind cycling or from original installation with roofing nails rather than the washer-head screws spec’d for high-wind zones. Anaheim’s 85-mph wind exposure rating means the fastener choice matters.
• Interior humidity spike after rain, confined to kitchen. A failed ice-and-water shield at the eave above the cabinet run lets vapor migrate through the ceiling plane without showing as a drip. This is common where the original builder spliced new shield to old without overlap.
• Sagging gutter at the cabinet corner only. The added roof area from a kitchen bump-out often exceeds the original gutter capacity; combined with debris from the adjacent oak canopy in Anaheim Hills neighborhoods, the hanger spacing fails first at the stress point.

Before

After

Replacement Cost & What’s Included

For Anaheim, KraftMaid-adjacent roofing repair runs $400-$1,800 depending on how many linear feet of flashing need removal, whether the underlying plywood is sound, and whether we are matching a discontinued shingle color. Full replacement of the affected roof plane, typical when the kitchen expansion roof was tied in with a incompatible pitch, ranges $8,000-$20,000. Every quote we write itemizes: demolition and haul-away, substrate inspection with photo documentation, new underlayment to current Title 24 cool-roof specs where required, installation, and permit closure.

Under Clause 1 of the Haven Standard, that price is written before anyone picks up a tool. Changes happen only with a signed change order, which is why our projects finish within a few percent of the number we agreed on. The 365-Day Done Right Promise covers the workmanship; material warranties run per manufacturer spec, which we include in your written packet.

DIY or Call Us?

An owner can safely check the gutter flow, look for daylight in the attic, and photograph any staining for reference. What you should not do: lift shingles to inspect flashing, walk a slope steeper than 3/12, or attempt to reseal a reglet joint. The step flashing at a roof-to-wall intersection is a system, not a strip; removing one piece without understanding the overlap sequence invites water behind the entire run. In Anaheim’s clay-heavy soil, that moisture migrates to the foundation, not just the ceiling.

We carry 26-gauge galvanized and 0.019-inch aluminum flashing on the truck, along with the compatible underlayment and fastener sets. Call (562) 245-4592 to schedule your free estimate. We’ll show you the photo record from inspection, name the part and the price in writing, and if you have a competitor’s quote, we’ll review it line by line at no charge.

FAQs